Tromber_Tenis MAT

Scraper for scraping compacted soil.

Galvanized iron teeth

Working width 1mt

• * Iron teeth replacement available

• Accessory to attach to Tromber
• Rigid nylon bristles.
• Aluminum support
• 2mt working width.
• To remove dirt after rain.
• Paddle court brushing.

Accessory for Tromber_tenis made of highly resistant rigid rubber

Working width: 100cm.

– For water collection

– To remove grit from the court

– To work the damp soil.

Metal brush to attach to Tromber_Tenis

Working width 1MT.

Iron spikes.

Adjustable height

Levels the top layer of red clay, achieving maximum planimetry of the court, removing compacted soil and distributing it throughout the court.

* Brush replacement available

It is an electric skate, small in size, customizable,

optimal for performing tennis court maintenance services

.

Its rear anchor allows the following tools to be adapted:

• Mat
• Wide yellow brush
• Toothed scraper
• Rubber scraper
• Metallic scratch brush
• Adjustable water roller.
• Trailer

Flexible hose made of plasticized food-grade PVC, with polyester textile reinforcement embedded in TPU resin, mechanically strong, blue exterior. Does not stain pavements when rubbed. Resistant to detergents, disinfectant solutions and low-content fats. Resistant to atmospheric agents. Working temperature: -5ºC to +60ºC

Price per 50 meters.

Accessory for Tromber_Tenis multi-tool

2 Layers of fine mesh PVC material, with final finish

Length: 1.15 meters

Aluminum rule

Working width: 2 meters

Range: 6.7 to 13.7 meters.
Pressure: 1.7 to 4.1 bar.
Flow rate: 0.34 to 1.91 m3/h.

• Double female thread lower inlet: ½” (15/21) and ¾” (20/27)

Female side inlet: ½” (15/21)
Trajectory angle:

23° for nozzles No. 06, 07, 08, 10 and 12
11° for nozzles 07-LA and 10-LA

• MPR Nozzles: 06 (red), 07 (black), 08 (blue), 10 (yellow), 12 (beige)
• Low angle nozzles: 07-LA (black), 10-LA (yellow)

• Superior quality aluminum umpire chair, powder-coated, GS tested according to DIN EN 131.
• Wider non-slip steps and the outstanding support with four feet provide optimum stability.

The tray between the steps of the ladder provides additional stability and serves as a storage area.

The seat support also has a cross brace behind the UV-resistant plastic seat.

A folding plastic writing board is included.

• Seat height 1855 mm – projection 1505 mm – front width 760 mm

Set of two cylinders with metal spikes.

Galvanized and oven-dried painted finish.

Easy adaptation to the motor hoe.

Ideal for milling the court, does not lift the rubble.

Axle included.

Adapter accessory for roller and brush.

With seat

Support pedals.

Easy assembly.

Size: 12.70m long, 1.07m high

• Black polyethylene braided thread, 3.8 mm, green with 4.5 cm mesh.
• Hand-knotted, 6 double rows.
• Upper band, made of polyester mesh with 4 stitches. Interior steel cable covered with plastic.

Sides and lower edges with resistant black plastic edges-

• Two 10 mm thick fiberglass rods for lateral fixation.

High quality net.

• Resistant to UV rays, weathering and color resistant.

3 year factory warranty on the net. GS tested according to DIN EN 1510.

High Tenacity Polypropylene Thread

4mm thick net, 43mm mesh width.

White Polyester Top Band

Polyester tape on the sides and black trim on the bottom

One eyelet in each corner of the net and 3mm double tension cord.

6mm plasticized steel cable