Cement line set BL

Prefabricated white cement lines, with 2 galvanized iron rods inside.

Width 5 cm.

Length 1.20 meters.
Sold per unit.

Line marker for precision lines, especially for marking on artificial and natural grass.

Maintenance-free.

No Maintenance or Cleaning Required

Ergonomic handle.

Comfortable start-up trigger

Tracing width adjustment: 3 to 10 cm.

The aerosol can holder is reinforced

The wind guard ensures perfect marking

Highly resistant reinforced metal chassis.

Lateral support for marking at the edge of pallets, machines, walls, etc.

Aerosol can compartment for quick paint availability

Includes tracing cord and can of az

Prefabricated white cement lines, with 2 galvanized iron rods inside.

Width 5 cm.

Length 1.20 meters.

Sold per unit.

Special paint for floors, highly resistant and with high pigmentation.

– Resistant to traffic, inclement weather, and hydrocarbons.

– Quick-drying paint.

– CFC and lead-free paint.

– 7 colors available.
Price per box of 12 units

Flexible profile made of hard PVC, white color

Transverse grooves 4 mm wide, at 28 mm intervals.

18 pieces of anchor pipe

4 rolls of 24 m = 4 cm

1 roll of 22 m = 5 cm wide

• 1 roll of 30 m = 5 cm wide
• Material needed for the installation of a court, which can be done by one person
• * The use of hard PVC and cross slits results in excellent anchoring with the surface of the court.

• Galvanized ratchet tensioner with fastening anchors and special straps for tensioning the Speziala tennis line.

Anchor set for the installation of Speziala lines: II

18 stainless steel tubular anchors

• 8 pieces with 4 cm anchors

10 pieces with 5 cm anchors.

Special pegs for artificial turf.

Pack of 100 units.

Posts made of 80 mm round steel, designed to be anchored to the ground

using metal canisters -not included-. Includes tensioning ratchet to tighten the net cable to be placed, in

the upper part they have the net height adjustment system, which allows playing volleyball in its different categories and by

lastly the lower part is provided with the corresponding hitches for the practice of tennis. Post measurements:

280cm

• The Oslo bench is manufactured with ductile iron feet with Ferrus treatment for corrosion protection. Coated with Marson-colored polyester powder paint.
• The five tropical wood planks are treated with a triple layer of Lignus coating, a fungicide, insecticide, and water repellent protector.

All the screws are made of stainless steel.
Recommended anchoring: Using M10 expansion bolts depending on the surface and project.

Pine wood treated in autoclave with class 4 vacuum-pressure against woodworm, termites, and insects. Planks of 1940 × 95 × 45mm.

• Steel bicycle rack with Ferrus anti-corrosion treatment. The Ferrus treatment involves applying an electrolytic bath to the piece, followed by a layer of epoxy primer and finally a coating of gray RAL 9006 powder polyester paint.

Recommended anchoring: Using 4 M8 expansion bolts, depending on the surface and project.

Range: 6.7 to 13.7 meters.
Pressure: 1.7 to 4.1 bar.
Flow rate: 0.34 to 1.91 m3/h.

• Double female thread lower inlet: ½” (15/21) and ¾” (20/27)

Female side inlet: ½” (15/21)
Trajectory angle:

23° for nozzles No. 06, 07, 08, 10 and 12
11° for nozzles 07-LA and 10-LA

• MPR Nozzles: 06 (red), 07 (black), 08 (blue), 10 (yellow), 12 (beige)
• Low angle nozzles: 07-LA (black), 10-LA (yellow)

• The exact height adjustment is done manually with 2 wing nuts, independently on each side, so the milling depth can be determined with millimeter precision.
• The milled material is ejected and can be transported in wheelbarrows with little effort.

The power of the 5.5 hp Honda engine ensures that the blade runs absolutely smoothly, so that the tracks remain flat or become flat again.

• The front part consists of 2 independently mounted rollers. This distributes the pressure evenly so that it hardly sinks in spring, even when thawing.

Solid rubber rear wheels without profile and the low weight make the device extremely agile and mobile.

• It adapts to all access doors and can be easily operated by a single person.

TECHNICAL DETAILS:

• – Engine: Honda, 4-stroke, 4.0 kW / 5.5 HP

– Length: approx. 800 mm

– Width: approx. 850 mm.

– Height: approx. 1000 mm

– Milling width: approx. 655 mm

– Weight: approx. 75 kg

* Honda engine warranty