Lawn installation peg

Joint tape for the installation of turf.

0.15x25mt roll.

Anti-weed textile mesh, made of polypropylene.

Resistant to dry rot and fungal attacks.

It is applied as an anti-weed sheet, placed under vegetable or mineral mulching.

2x100mt

Two-component PU adhesives consist of a resin (component A) and a hardener (component B), mixed in a defined proportion. of two-component adhesive.

5KG can.

The adhesive performance is approximately 0.40/0.60 kg of adhesive per M2.

All our adhesives are certified according to UNE-EN 13744:2006 and UNE-EN 12228:2002 regulations required by FIFA for the installation of artificial turf in accredited and approved sports fields and facilities.

• Silica sands are the most ecological and natural in Spain, free of chemical products (amines and hydrofluoric acid) and without salinity. Washed exclusively with natural waters and dried with biomass.
• They are characterized by being aeolian, round or spheroid sands, without edges, allowing the product not to cake or compact, facilitating drainage. Granulometries: 0.2-0.5s/ 25kg

SILICA PALLET 1,200kg – 48sacksx25kg

Seaming tape for lawn installation.

0.30x25mt roll.

Two-component PU adhesives consist of a resin (component A) and a hardener (component B), mixed in a defined proportion. of two-component adhesive.

12KG can.

The adhesive performance is approximately 0.40/0.60 kg of adhesive per M2.

All our adhesives are certified according to UNE-EN 13744:2006 and UNE-EN 12228:2002 regulations required by FIFA for the installation of artificial turf in accredited and approved sports fields and facilities.

Textile anti-weed mesh, made of polypropylene.

It is applied as an anti-weed sheet, for artificial grass base, professional growers, gardeners.

Roll size:
1.50x20mt = €46

1.50x40mt = €75

2.10x100mt = €180

* Other sizes or thicknesses consult

Special pegs for artificial turf.

Pack of 100 units.

Fountain with a sober structure, square iron body with Ferrus treatment to prevent corrosion.

Finished with epoxy primer and gray hammered powder polyester paint.

Fixing plate-nickel-plated steel push button tap (UM510G). Angular frame and galvanized steel drain grid.

• The Oslo bench is manufactured with ductile iron feet with Ferrus treatment for corrosion protection. Coated with Marson-colored polyester powder paint.
• The five tropical wood planks are treated with a triple layer of Lignus coating, a fungicide, insecticide, and water repellent protector.

All the screws are made of stainless steel.
Recommended anchoring: Using M10 expansion bolts depending on the surface and project.

Pine wood treated in autoclave with class 4 vacuum-pressure against woodworm, termites, and insects. Planks of 1940 × 95 × 45mm.

• Steel bicycle rack with Ferrus anti-corrosion treatment. The Ferrus treatment involves applying an electrolytic bath to the piece, followed by a layer of epoxy primer and finally a coating of gray RAL 9006 powder polyester paint.

Recommended anchoring: Using 4 M8 expansion bolts, depending on the surface and project.

Equipped with a new anti-injury system for net placement, guide rod instead of hook.

All our hoops have the same wheelbase, 7 cm high x 8.50 cm wide.

Prefabricated white cement lines, with 2 galvanized iron rods inside.

Width 5 cm.

Length 1.20 meters.
Sold per unit.

• The exact height adjustment is done manually with 2 wing nuts, independently on each side, so the milling depth can be determined with millimeter precision.
• The milled material is ejected and can be transported in wheelbarrows with little effort.

The power of the 5.5 hp Honda engine ensures that the blade runs absolutely smoothly, so that the tracks remain flat or become flat again.

• The front part consists of 2 independently mounted rollers. This distributes the pressure evenly so that it hardly sinks in spring, even when thawing.

Solid rubber rear wheels without profile and the low weight make the device extremely agile and mobile.

• It adapts to all access doors and can be easily operated by a single person.

TECHNICAL DETAILS:

• – Engine: Honda, 4-stroke, 4.0 kW / 5.5 HP

– Length: approx. 800 mm

– Width: approx. 850 mm.

– Height: approx. 1000 mm

– Milling width: approx. 655 mm

– Weight: approx. 75 kg

* Honda engine warranty