Replacement court sweeper

Support: Galician pine wood

Fiber: 1.2mm strong black PVC

Sewn: With galvanized wire

• Galician wood handle 1.2 meters long, adjusted with metal clamp

Galvanized solid iron tamper or rammer.

Wooden handle.

For small court repairs and tablet pressing.

Working surface: 20x20cm.

Metal mesh sieve or screen.

Various mesh thicknesses from 1.40 to 6.10mm.

To achieve perfect homogenization of the clay court.

Fixing bracket with 2 hooks for hanging hand brushes, mats, etc.

Made of steel, green, plastic-coated for Ø 60 mm posts.

Absorbent drum with foam covering.

• Structure and body of the drum, hot-dip galvanized.
• Thanks to the high absorbency of this roller, it is possible to dry the court in a very short period of time.

Working width 80 cm.

2 Layers of fine mesh PVC material, with a final finish

Length: 1.15m

Aluminum ruler

Working width: 3m

1.2mm prolipoptrilene bristles.

Arch-shaped handles and aluminum profile.

2mt working width.

To remove dirt after rain.

For brushing the court.

• * IDEAL TOOL FOR TROMBER TENNIS

• Chemical product composed of flakes that dissolve on the court, forming a waterproof solution down to -10ºC, European manufacturing.
• WINTER. With proper treatment, the courts are prevented from freezing and remain usable throughout the winter, avoiding deterioration, which would involve the compaction of the softened ground.

SUMMER. Absorbs ambient humidity, keeping the court moist without the need for watering.

• PALLET OF 1250KG 50 bags of 25kg.

• Trash can with semi-circular folding steel bucket with triangular holes with Ferrus treatment to treat corrosion. Final coating of gray RAL 7011 polyester powder paint. Bucket supported on a 40 mm tube structure with an anchoring base and rectangular plates with 2 12 mm holes for fixing to the ground.

Measurements: 455mm diameter, 605mm total height.

Recommended anchoring: By means of four M8 expansion bolts depending on the surface and project.

• Steel bicycle rack with Ferrus anti-corrosion treatment. The Ferrus treatment involves applying an electrolytic bath to the piece, followed by a layer of epoxy primer and finally a coating of gray RAL 9006 powder polyester paint.

Recommended anchoring: Using 4 M8 expansion bolts, depending on the surface and project.

Set of nets for 2 polypropylene handball goals.

Different sizes, colors and designs available.

100mm knotless square mesh, knotless

Mesh of 3, 4, 4.5 and 5mm thick.

* Catalog attached – Request a quote

BASIC BADMINTON C-PVC SUPERIOR

-Size: 1.85×1.22m

-Made with High Tenacity Polypropylene Thread.

-2mm thick net, 18mm mesh width.

-White PVC top band, black polyester trim on the sides and bottom of the net.

-One eyelet in each upper corner of the net and double tension cord of 0.3mm.

-0.4mm plasticized steel cable.

* Also available in BASIC BADMINTON C-PES SUPERIOR and HIGH COMPETITION BADMINTON C-PS SUPERIOR.

Prefabricated white cement lines, with 2 galvanized iron rods inside.

Width 5 cm.

Length 1.20 meters.
Sold per unit.

Aluminum rake with soft rubber teeth

Wooden handle.

For collecting leaves and surface dirt from the court.

Width: 75cm.

Aluminum profile.

Aluminum handle

High-strength rigid rubber

Working width: 100cm.

– For water collection

– To remove grit from the court

– For working damp soil.

Range: 6.7 to 13.7 meters.
Pressure: 1.7 to 4.1 bar.
Flow rate: 0.34 to 1.91 m3/h.

• Double female thread lower inlet: ½” (15/21) and ¾” (20/27)

Female side inlet: ½” (15/21)
Trajectory angle:

23° for nozzles No. 06, 07, 08, 10 and 12
11° for nozzles 07-LA and 10-LA

• MPR Nozzles: 06 (red), 07 (black), 08 (blue), 10 (yellow), 12 (beige)
• Low angle nozzles: 07-LA (black), 10-LA (yellow)

Accessory for Tromber_tenis, Multiherramienta or manual use

Roller with cleaning brush.

Capacity 330L

Working width 1MT.

Painted with oven drying.

Stainless steel bearings.